Step 1 - Create a cross-shaped parting to divide the hair into four areas, using a point 1 cm beyond the crown as a reference. Create a curved parting starting at the end of the left eyebrow and ending three quarters of the way across the right eyebrow. Create curved partings in the left and right temporal areas, using the occipital bone as a reference.
Step 2 - Create a wide horizontal zigzag parting and develop two micro-sections. In the first area, backcomb to 70% and apply Maraes Lightening Powder mixed 1:2 with Maraes Activator. Continue with backward diagonal zigzag partings, working from the right temple towards the left and progressively increasing the thickness of the sections. Backcomb to 70%.
Step 3 - Create backward diagonal zigzag partings, working from right to left and progressively increasing the thickness of the sections. Backcomb to 70%.
Step 4 - Once a lift level of 7/8 has been reached, rinse and pre-dry the hair to 70%. Apply Maraes Demi Permanent. Roots: 20 g 5.44 + 10 g 6.88 + 10 g 4.2 + 60 g Maraes Activator 10 vol. Mid-lengths and ends: 20 g 5.44 + 10 g 6.88 + 10 g 4.2 + 60 g Maraes Activator 6 vol. + 16 ml Maraes pH Reducer. Development time: 20 minutes. Then rinse and shampoo.
Step 1 - (A) Section: Horizontal | Distribution: Perpendicular | Elevation: 90°+ | Finger position: Parallel to the section. Cutting technique: Blunt cutting | Cutting line: Progressive layers with a travelling guide. (B) Section: Horizontal | Distribution: Perpendicular | Elevation: 90°+ | Cutting technique: Progressive layers using multiple strands.
Step 2 - Section: Vertical | Distribution: Overdirected | Elevation: 90°+ | Finger position: Not parallel to the section
Cutting technique: Slide cutting | Cutting line: Progressive layers with a stationary guide.
Cutting technique: Slide cutting | Cutting line: Progressive layers with a stationary guide.
Step 3 - Section: Vertical | Distribution: Perpendicular | Elevation: 90°+ | Finger position: Parallel to the section
Cutting technique: Blunt cutting | Cutting line: Progressive layers using multiple strands
Cutting technique: Blunt cutting | Cutting line: Progressive layers using multiple strands
Step 4 - Section: Single block | Distribution: Overdirected | Elevation: 90°+ | Finger position: Not parallel
Cutting technique: Blunt cutting | Cutting line: Progressive layers with a stationary guide
Cutting technique: Blunt cutting | Cutting line: Progressive layers with a stationary guide
Step 1 - Create horizontal partings. Hold the straightener horizontally in the right hand. Perform a 90° inward rotation, sliding for 2 cm; then move the hand into a diagonal position and continue sliding through the entire length. At the ends, position the straightener vertically and glide to the tips. Use the left hand on the next section and repeat, alternating throughout the area.
Step 2 / 3 - Create horizontal partings. Hold the straightener horizontally in the right hand. Perform a 90° inward rotation, sliding for 2 cm; then move the hand into a diagonal position and continue through the entire length. At the ends, position the straightener vertically and glide to the tips. Use the left hand on the next section and repeat, alternating throughout the area.
Step 2 / 3 - Create horizontal partings. Hold the straightener horizontally in the right hand. Perform a 90° inward rotation, sliding for 2 cm; then move the hand into a diagonal position and continue through the entire length. At the ends, position the straightener vertically and glide to the tips. Use the left hand on the next section and repeat, alternating throughout the area.
Step 4 - Create horizontal partings. Hold the straightener horizontally in the left hand. Perform an ascending 90° inward rotation, sliding for 3 cm. Position the straightener diagonally and continue through the full length to the ends. At the ends, position the straightener vertically and glide to the tips.
Styling: Volook, Primer, Diamond Smooth | Finish: Fixer, Texture
Styling: Volook, Primer, Diamond Smooth | Finish: Fixer, Texture
